|
The Range Control Set
The inlet control set on every Tribune HE units is of
a well-proven 'high-flow' design, allowing flows in excess of 50L/min.
The set combines a pressure reducing valve, complete with strainer,
non-return valve and expansion relief valve with provision for expansion
vessel and balanced cold connections.
The operating pressure is 3 bar, but the valve will continue to give
good performance down to an inlet pressure of 1 bar.
Coil-in-Coil Heat Exchanger
With its large surface area you are assured of fast
reheats. The smaller sizes of Tribune HE exceed the CheSS best practice
guidelines.
Either coil connection can be used as the inlet. Reheat performance is
equally good either way.
In reaching right down to the bottom of the cylinder, the coil-in-coil
heats the Tribune HE's entire capacity. A sophisticated cold water
baffle helps preserve the stratification and prevent mixing during water
draw-off. As a result, a 150 litre Tribune HE produces 150 litres of hot
water - as simple as that!
Environmentally Friendly Insulation
As you would expect, Tribune HE is very well
insulated. A class leading 50mm thick insulation layer surrounds the
cylinder. Coupled with the close-fitting case, Tribune HE's heat loss is
low.
Heat loss figures meet CheSS best practice guidelines for insulation.
The insulation is CFC-Free, HCFC-Free and contains no ozone-depleting
chemicals.
External Expansion Vessel - Flexible and
Reliable
We have chosen to use an external expansion vessel for
our Tribune HE. With no air bubble to lose it promises improved
reliability. Add flexible siting and reduced overall height and you have
a winning combination.
Comprehensive kit of parts with every unit
We've not cut corners in our kit of parts. You get all
the components you need to complete the installation - just add pipework.
This attention to detail means no lost time making a trip to the
merchants and no hidden costs involved when you buy a Tribune HE.
|
|
Expansion Vessel
Part Nos.:
12 Litre - TS312
18 Litre - TS318
24 Litre - TS325 |
|
|
Expansion
Vessel Hose
Part No. TS314 |
| |
|
|
|
|
Wall Mounting Kit
for Expansion Vessel
Part No. TS316-12L
Expansion Vessel Bracket
Part No. TS317-18/24L
|
|
|
High Flow Rate
Inlet Control Set
Part No. TS301 |
| |
|
|
|
|
10 Way
Electrical Box
Part No. TS106
|
|
|
V4043H
Two Port Valve
Part No. TS5 |
| |
|
|
|
|
Temperature and
Pressure
Relief Valve
Part No. TS302
|
|
|
Incoloy Long Life
3kW Immersion
Heater
Part No. TS9 |
| |
|
|
|
|
Acetal Tundish
Part No. TS303
|
|
|
Installation &
Maintenance
Instructions |
| |
|
|
|
|
Dual Thermostat
Part No. TS207
|
|
|
Benchmark
Logbook |
| |
|
|
|
Twin Coil Only
|
| |
|
|
|
|
Single Thermostat
Part No. TS27
|
|
|
HL Thermostat
Part No. TS28 |
|
Tribune HE comes complete with all the fittings you need
to complete the installation:
DIRECT PARTS (ELECTRIC)
> Inlet Control set
> Temp & Pressure relief valve
> 15mm / 22mm Tundish
> Expansion vessel
> Wall mounting bracket
> Expansion vessel hose
> 2 x Immersion Heaters (1 on 60L and 90L)
> Installation & Maintenance Instructions
> Benchmark Logbook
INDIRECT PARTS (GAS/OIL)
> Inlet Control set
> Temp & Pressure relief valve
> 15mm / 22mm Tundish
> Expansion vessel
> Wall mounting bracket
> Expansion vessel hose
> Immersion Heater (2 on 250 & 300 litre)
> Two port zone valve
> Wiring centre
> Dual Thermostat
> Installation & Maintenance Instructions
> Benchmark Logbook
TWIN COIL PARTS (RENEWABLE ENERGY SOURCE)
> Inlet Control set
> Temp & Pressure relief valve
> 15mm / 22mm Tundish
> Expansion vessel
> Wall mounting bracket
> Expansion vessel hose
> Immersion Heater
> 2 x Two port valves
> Wiring centre
> Dual Thermostat
> Single Thermostat
> High Limit Thermostat
> Installation & Maintenance Instructions
> Benchmark Logbook
For Parts and Spares ring 01924
|
