• Hercal
• Supercal
• Ultracal
• Primatic
• Direct
• Super 7 Direct
• Dublo
• Fortic
• Flowmax
• Tribune HE

For over 80 years, Range have been synonymous with quality. The Range brand has embodied all the hallmarks of manufacturing excellence and product innovation. All Range factories work to and are accredited to ISO 9001 Exhaustive research and development has culminated in the new Tribune HE family of Duplex stainless steel unvented cylinders. Tribune aims to set new benchmarks for quality, performance and endurance. With 25 models in its product range, there is sure to be a Tribune HE capable of fulfilling your needs today and long into the future. > Duplex stainless steel for ultimate peace of mind > Fully transferable 25 year guarantee > High flow-rate controls - ideal for multiple bathrooms & power showering > Fast reheat and high insulation values resulting in high efficiency > A Complete package - just add pipework > Electric/Direct and Gas-Oil/Indirect 8 sizes 60-300 litres Twin Coils - Solar etc 4 sizes 180-300 litres Slimline - 6 sizes 60-210 litres > Plug-in, Pre-plumbed units available, saving extra time and providing continuity on multiple installations.

Duplex stainless steel is extremely environmentally friendly. As a material it is 100% recyclable in fact over 90% of new stainless steel comes from old re-melted stainless steel. Stainless steel will go on to complete full life cycles indefinitely.

Fully Transferable 25 year guarantee

Its Strength Is In Its Detail...

The beauty of the Range Tribune HE is not only skin deep. Take a look inside. See for yourself how we've combined the highest manufacturing standards with tried and tested values, control sets and thermostats from renowned manufacturers.

The Range Control Set The inlet control set on every Tribune HE units is of a well-proven 'high-flow' design, allowing flows in excess of 50L/min. The set combines a pressure reducing valve, complete with strainer, non-return valve and expansion relief valve with provision for expansion vessel and balanced cold connections. The operating pressure is 3 bar, but the valve will continue to give good performance down to an inlet pressure of 1 bar. Coil-in-Coil Heat Exchanger With its large surface area you are assured of fast reheats. The smaller sizes of Tribune HE exceed the CheSS best practice guidelines. Either coil connection can be used as the inlet. Reheat performance is equally good either way. In reaching right down to the bottom of the cylinder, the coil-in-coil heats the Tribune HE's entire capacity. A sophisticated cold water baffle helps preserve the stratification and prevent mixing during water draw-off. As a result, a 150 litre Tribune HE produces 150 litres of hot water - as simple as that! Environmentally Friendly Insulation As you would expect, Tribune HE is very well insulated. A class leading 50mm thick insulation layer surrounds the cylinder. Coupled with the close-fitting case, Tribune HE's heat loss is low. Heat loss figures meet CheSS best practice guidelines for insulation. The insulation is CFC-Free, HCFC-Free and contains no ozone-depleting chemicals. External Expansion Vessel - Flexible and Reliable We have chosen to use an external expansion vessel for our Tribune HE. With no air bubble to lose it promises improved reliability. Add flexible siting and reduced overall height and you have a winning combination. Comprehensive kit of parts with every unit We've not cut corners in our kit of parts. You get all the components you need to complete the installation - just add pipework. This attention to detail means no lost time making a trip to the merchants and no hidden costs involved when you buy a Tribune HE.

Expansion Vessel Part Nos.: 12 Litre - TS312 18 Litre - TS318 24 Litre - TS325 Expansion Vessel Hose Part No. TS314         Wall Mounting Kit for Expansion Vessel Part No. TS316-12L Expansion Vessel Bracket Part No. TS317-18/24L     High Flow Rate Inlet Control Set Part No. TS301         10 Way Electrical Box Part No. TS106     V4043H Two Port Valve Part No. TS5         Temperature and Pressure Relief Valve Part No. TS302     Incoloy Long Life 3kW Immersion Heater Part No. TS9         Acetal Tundish Part No. TS303     Installation & Maintenance Instructions         Dual Thermostat Part No. TS207     Benchmark Logbook         Twin Coil Only         Single Thermostat Part No. TS27     HL Thermostat Part No. TS28

Tribune HE comes complete with all the fittings you need to complete the installation: DIRECT PARTS (ELECTRIC) > Inlet Control set > Temp & Pressure relief valve > 15mm / 22mm Tundish > Expansion vessel > Wall mounting bracket > Expansion vessel hose > 2 x Immersion Heaters (1 on 60L and 90L) > Installation & Maintenance Instructions > Benchmark Logbook INDIRECT PARTS (GAS/OIL) > Inlet Control set > Temp & Pressure relief valve > 15mm / 22mm Tundish > Expansion vessel > Wall mounting bracket > Expansion vessel hose > Immersion Heater (2 on 250 & 300 litre) > Two port zone valve > Wiring centre > Dual Thermostat > Installation & Maintenance Instructions > Benchmark Logbook   TWIN COIL PARTS (RENEWABLE ENERGY SOURCE) > Inlet Control set > Temp & Pressure relief valve > 15mm / 22mm Tundish > Expansion vessel > Wall mounting bracket > Expansion vessel hose > Immersion Heater > 2 x Two port valves > Wiring centre > Dual Thermostat > Single Thermostat > High Limit Thermostat > Installation & Maintenance Instructions > Benchmark Logbook For Parts and Spares ring 01924 376026

Using Tribune HE Units In Parallel

For applications where very high flow rate or larger amounts of storage are required two or more Tribune HE units can be linked in parallel. When linking two cylinders a serparate cold feed is taken to each one and the outlets are joined together. The flow rate available doubles (subject to the cold main). The demand for hot water will vary considerably between types of buildings and the activities taking place there. For example: An office building will require small quantities frequently to many outlets during normal & overtime office hours. A factory production line will have a peak demand at the breaks in the shift or at the end when the work force may all want to wash their hands simultaneously. A Sports Pavilion will need to be able to provide large quantities of hot water for the teams showering needs over a short period of time after the game. So your selection must take into account a number of things: 1. The maximum simultaneous hot water demand 2. The total hot water demand required 3. The required system reheat time http://www.hot-water-cylinders.com/Range-Tribune-HE_c_990-1.html

Applications Using Tribune HE Solar Units

Also suitable for other renewable energy sources Twin coil Tribune HE's can be used in various ways: 1) To couple two different boilers up to the Tribune HE 2) For systems with solar heating. Solar heat is fed in via the lower coil. 3) Heat pump 4) Bio-mass 5) Micro-CHP IMPORTANT NOTICE It is a requirement of building regulations that any heat source connected to an Unvented cylinder (such as Tribune HE) be under full thermostatic control and are able to turn themselves COMPLETELY off As a result you cannot connect an Aga (or equivalent) or a solid fuel stove to a Tribune HE.   http://www.hot-water-cylinders.com/Range-HE-Solar-Cylinders_c_992-1.html

These recommendations are based on guidelines in BS 6700. Guidance should be sought for unusual applications. E.g. High flow-rate showers, large baths etc.   Hot Water Demand Bedrooms Gas/Oil Indirect Electric Direct         1 Bathroom or Shower Bedsit / 1 Bed 60/90/100 150   2-3 Bed 120 180   3-4 Bed 150 210         1 Standard Bath 2-3 Bed 120 210   3-4 Bed 120 210         2 Bath and En-suite 2-3 Beds 150 210   3-4 Beds 150 210   4-5 Beds 180 250         2 Standard Baths 2-3 Bed 180 210   3-4 Bed 180 210   4-5 Bed 210 250         3 Bathrooms 3-4 Bed 250 300   4-5 Bed 250 300   5-6 Bed 300 300

Typical commercial application Indirect     Large House - 6 bed / 4 bathrooms 2x 210 Guest House - 8 bed / 4 bathrooms 2x 300 Small Hotel - 8 bed / 8 bathrooms 3x 210 Sports Pavillion (25 people / 4 showers) 2x 300 Sports Pavillion (25 people / 6 showers ) 3x 210 Student House (25 people / 3 bathrooms) 3x 300 Old Peoples' Home (60 beds / 10 bathrooms) 5x 300 each supplying 2 bathrooms Example illustration A school swimming pool has 5 showers in each of two changing rooms. The shower heads are flow-restricted to 9 ltrs per minute (2/3rds of this will be hot water). Usually there are 3 one hour lessons each morning and three each afternoon. Assuming a class size of 30 children. Maximum demand = 10 shower heads x 9 litres / min = 90 litres / min. This is more than one Tribune HE can supply. At least two Tribune HEs will be needed to provide this ( see flowrate graphs ) Total demand = 30 kids x 6 litres / minutes x 5 minute shower = 900 litres 3x 300 litre units will be required Reheat time has to be a maximum of one hour so it is reheated in time for the next lesson. A TI300 can reheat its entire contents in 60 minutes with a boiler power of 15kW. So total boiler power required = 45kW If direct units were used it would have to be fitted with immersion heaters rated at 15kW (typically 1 x 9kW + 1 x 6kW)

Regulations All unvented units with a capacity over 15L capacity must be installed by a competent installer in accordance with the following Regulations: England and Wales - Building Regulation G3 Scotland - Technical Standard P3 N Ireland - Building Regulation P5 Siting With no header tanks to consider, Tribune HE units can be sited almost anywhere in the house. Tribune HE can supply outlets both above and below its location. Tribune HE must be fixed VERTICALLY on a flat surface capable of holding its weight.   Water Supply An adequate water supply is vital to ensure Tribune HE produces the high performance of which it is capable. We recommend a minimum supply of 1.0 bar with a flow rate of 25 litres/min. The maximum supply pressure is 16 bar.   Compatible Boilers Gas or oil fired fitted with an integral control thermostat and cut-out. Any heat source that lacks full thermostatic control such as most solid fuel boilers, Agas, Rayburns and Stanleys cannot normally be connected to any unvented system. The Primary circuit may be Open Vented or Sealed (operating at up to 7 bar). The primary circuit must be pumped.   Connection Sizes Cold Inlet - 22mm compression. Hot Outlet - 22mm compression. Coil connections - 22mm compression. Safety Valves - 15mm compression outlet. Inlet Control Set - 22mm compression inlet and outlet. Tundish - 15mm compression inlet / 22mm compression outlet.   Secondary Return A dedicated 22mm secondary return connection is fitted to 210, 250 and 300 litre sizes. A swept tee (not supplied) could be used to provide a secondary return on the smaller sizes.   Electrical Wiring Controls should be wired to the boiler / programmer etc. in accordance with the control scheme being used. Although compatible with Y, W or S Plan layouts, Tribune HE units are perhaps best suited to installation as an S Plan since we already supply one of the two port valves necessary, so reducing installation costs compared to other plans. Each immersion heater must have a permanent connection via a double pole-linked isolating switch with a minimum rating of 13 amps. All electrical wiring must comply with the latest IEE wiring regulations.

Model Reheat Time Coil kW Rating 60 11 minutes 16.5kW 90 13 minutes 16.5kW 120 17 minutes 16.5kW 150 17 minutes 18.9kW 180 21 minutes 18.9kW 210 22 minutes 18.9kW 250 28 minutes 21.4kW 300 36 minutes 21.4kW The reheat performance is measured from 15°C to 60°C after drawing off 70% of the capacity. The coil kW rating is a guide to the minimum size of boiler required to achieve the reheat times stated. direct reheat performance   Model Reheat Time Coil kW Rating   one element two elements 60 45 minutes - 90 35 minutes - 100 58 minutes - 120 90 minutes 45 minutes 150 121 minutes 62 minutes 180 157 minutes 79 minutes 210 192 minutes 96 minutes 250 224 minutes 112 minutes 300 263 minutes 132 minutes   immersion heaters Tribune is fitted with Immersion Heater as follows:   Size Direct Indirect Twin Coil 90 Litre One Immersion Heater One Immersion Heater Not Made 120 Litre Two Immersion Heaters One Immersion Heater Not Made 150/180/210 Litre Two Immersion Heaters One Immersion Heater One Immersion Heater 250/300 Litre Two Immersion Heaters Two Immersion Heaters One Immersion Heater   flow rates Tribune Unvented Pressure V Flow Performance (measured at 50% Backpressure to simulate the effect of the drawoff pipework and taps)

Direct Specification

Code Capacity Height Diameter D F Weight Weight             (kg-empty) (kg-Full)                 TD90 90 L 718 550 N/F N/F 25 115 TD120 120 L 906 550 N/F 510 30 150 TD150 150 L 1093 550 N/F 610 35 185 TD180 180 L 1281 550 N/F 710 40 220 TD210 210 L 1469 550 1000 810 45 255 TD250 250 L 1719 550 1250 950 50 300 TD300 300 L 2032 550 1500 1100 55 355   http://www.hot-water-cylinders.com/Direct_c_995-1.html

Code Cap. Height Dia. A B C D E F Weight Weight                     (kg-empty) (kg-Full)                         TI90 90 L 718 550 290 330 390 345 N/F N/F 30 120 TI120 120 L 906 550 290 330 390 345 N/F N/F 35 155 TI150 150 L 1093 550 330 370 465 385 N/F N/F 40 190 TI180 180 L 1281 550 330 370 465 385 N/F N/F 45 225 TI210 210 L 1469 550 365 405 465 465 N/F 1150 50 260 TI250 250 L 1719 550 365 405 465 560 950 1400 55 305 TI300 300 L 2032 550 365 405 465 660 1100 1600 60 360   http://www.hot-water-cylinders.com/Indirect_c_996-1.html

CODE CAPACITY HEIGHT DIAMETER A B C D E F WEIGHT (Kg-EMPTY) WEIGHT (Kg-FULL) TT180 180 L 1281 550 330 385 465 N/F 825 880 50 230 TT210 210 L 1469 550 365 420 465 775 925 980 55 265 TT250 250 L 1719 550 365 420 465 1250 1050 1105 60 310 TT300 300 L 2032 550 365 420 465 1500 1200 1255 65 365 http://www.hot-water-cylinders.com/Range-HE-Solar-Cylinders_c_992-1.html

http://www.hot-water-cylinders.com/Range-HE-Slimline-Cylinders_c_993-1.html

Indirect CODE CAPACITY HEIGHT DIAMETER A B C D WEIGHT (KG-EMPTY) WEIGHT (KG-FULL) TIS60 60 L 673 478 290 330 390 345 25 80 TIS90 90 L 1048 478 290 330 390 345 30 130 TIS120 120 L 1236 478 290 330 390 345 35 155 TIS150 150 L 1424 478 330 370 470 470 40 190 TIS180 180 L 1674 478 330 370 470 560 45 225 TIS210 210 L 1987 478 330 370 470 660 50 260 http://www.hot-water-cylinders.com/Indirect_c_996-1.html

Direct CODE CAPACITY HEIGHT DIAMETER F WEIGHT (KG-EMPTY) WEIGHT (KG-FULL) TDS60 60 L 673 478 N/F - - TDS90 90 L 1048 478 600 25 115 TDS120 120 L 1236 478 700 30 150 TDS150 150 L 1424 478 800 35 185 TDS180 180 L 1674 478 900 40 220 TDS210 210 L 1987 478 1100 45 255 http://www.hot-water-cylinders.com/Direct_c_995-1.html

Save time and money with Tribune HE Systemfit, plug-in and pre-plumbed units The Ultimate plug-in, Pre-Plumbed Solution Tribune HE is available in a highly popular plug-in, pre-plumbed format - designed to significantly reduce the installation time. The units are factory assembled and are both pre-plumbed and pre-wired with 230V central heating controls, a pump, two 2-port motorised valves, automatic bypass and a balancing valve. All units are also supplied with programmer, room stat and both a central heating & hot water expansion vessel pack. This pre-plumbed Tribune HE System will not only speed up the installation process, but will also increase the quality and integrity of the central heating system. This results in an elimination of costly call-backs.   http://www.hot-water-cylinders.com/Range-Systemfit-Cylinders_c_994-1.html

features > 120, 150, 180, 250, and 300 litre capacities - s-plan  > Seven day programmer and room thermostat with timed domestic hot water (DHW) control  > Seperate central heating and hot water zones  > No maintenance three speed circulating pump  > Automatic bypass valve for system efficiency  > Load balancing valve for indirect coil efficiendy  > Connections for vented and unvented heating primaries.  >Plug in electrical connections for all controls benefits > Simplified on-site installation  > Up to 70% quicker to install  > Factory assembled for reliability - reduces costly call-backs and delays  > Consistent electrical and plumbing layout - neat, professional finish  > Greater customer satisfaction  > ISO 9001:2000 quality assured  > 25 year guarantee  > No tanks in the roof space & only requires a standard boiler  > Aids with Part P (Electrical wiring) as installer doesn't need an electrician on site to change any components, simply plug & go!   http://www.hot-water-cylinders.com/Range-Systemfit-Cylinders_c_994-1.html

The pre-plumbed Tribune HE System is manufactured from high grade materials inside and out, offering exceptional performance and reliability. ISO 9001:2000 Quality assured assembly > Consistent electrical and plumbing layout > Brazed pipework fabrication > Neat and tidy layout > Pre-wired and pre-plumbed Separate Central Heating and Hot Water Configuration > 22mm motorised valve to radiator circuit > 22mm motorised valve to coil heat exchanger > Wiring centre > Seven day programmer and room thermostat with timed Domestic Hot Water (DHW) control > Hot water temperature thermostat High Performance Configuration > Automatic bypass valve > 3 speed circulator pump with high quality isolating valves > Balancing valve > 22mm cold water combination valve (supplied loose) > Combined expansion valve/check valve housing > 22mm of 3/4" BSP hot outlet to taps > 22mm primary flow > 22mm primary return > Immersion heater with integral thermostat and thermal cut-out > Drain cocks > Comes complete with central heating expansion vessel pack and pressure gauge, as per inset shot below Comprehensive Safety Controls > Temperature and pressure relief valve operating at 90oC / 10 bar > 22mm tundish outlet > High limit hot water thermal cut-out   http://www.hot-water-cylinders.com/Range-Systemfit-Cylinders_c_994-1.html

Connections 1. 22mm hot water draw 2. Cold Water Inlet 3. Temperature Relief Valve 4. Cold Feed Drain Elbow 5. Immersion Heater 3kW 6. Twin Thermostat 7. Flow from Boiler 8. Circulating pump 9. 22mm Central Heating 2 port valve 10. Filling Loop Flexible Hose 11. Bottle Air Eliminator 12. 22mm DHW 2 Port valve/safety valve 13. Heating circuit drain elbow 14. 22mm Balancing valve (Lockshield) 15. 22mm Return from radiator circuit 16. 22mm Return to boiler 17. 22mm Automatic by-pass valve 18. Wiring Centre 19. Tundish • Plug-in sockets Code Capacity Height Diameter Weight Weight         (Kg-empty) (Kg - full)             TI120P 120 L 906 550 45 165 TI150P 150 L 1093 550 50 200 TI180P 180 L 1281 550 55 235 TI210P 210 L 1496 550 60 270 TI250P 250 L 1719 550 65 315 TI300P 300 L 2032 550 70 370 All Dimensions are in mm and are of the cased unit. N/F = not fitted. * More detailed information regarding the connection heights is available on request.   http://www.hot-water-cylinders.com/Range-Systemfit-Cylinders_c_994-1.html

Materials Inner shell - Duplex Stainless Steel Coil - 22mm Diameter Stainless Steel Bosses - Stainless Steel Every Tribune HE is water tested to a pressure of 15 bar.   Insulation Fire retardant polyurethane foam, nominal thickness 50mm. The foam is CFC-Free and HCFC-Free. The foam has an ozone depletion potential of ZERO and a Global Warming Potential of One.   Casework Zintec corrosion proofed steels throughout Durable, stove enamelled, gloss white paint finish   Anode None fitted / none required Expansion Vessel 12 Litre size with 60, 90, 120 and 150 Litre models 18 Litre size with 180, 210 and 250 Litre models 25 Litre size with 300 Litre model   Control Settings Pressure Reducing Valve - 3 Bar Expansion Relief Valve - 6 Bar Pressure and Temperature Relief Valve - 7 Bar/90°C High Limit Thermostat in Dual Thermostat - 85°C High Limit Thermostat in Immersion Heater - 85°C   Immersion Heater 13/4" BSP Parallel Threaded Head Long Life Incoloy Sheathed Low Noise Element 14" Long Long Life Incoloy Sheathed Thermostat Pocket 11" Long Brazed Construction 11" Combined Thermostat and Safety Cut-Out Element Rating 3Kw at 240V A/C   Approvals WRAS Approved to the Water Regulations WRC-NSF Approved to Building Regulations' G3 & L CE Compliant and fitted with a BEAB Approved Immersion Heater   Guarantee Terms The Tribune HE's stainless steel vessel carries a fully transferable, 25 year guarantee against faulty materials or manufacture provided that: It has been correctly installed as per the Installation Instructions and all the relevant standards, regulations and codes of practice in force at the time. It has not been modified in any way, other than by Range. It has not been misused, tampered with or subjected to neglect It has only been used for the storage of potable water. It has not been subjected to frost damage. The unit has been serviced annually The benchmark log book has been filled in after each annual service. The guarantee period starts from the date of purchase and no registration is required. Please note that invoices for servicing may be requested to prove that the unit has been serviced annually. All the components fitted to / or supplied with the Tribune HE carry a 2 year guarantee.   Exclusions - The Guarantee does not cover The effects of scale build up. Any labour charges associated with replacing the unit or its parts Any consequential losses caused by the failure or malfunction of the unit.